SEPTEMBER MEETING

ADDITIVE MANUFACTURING/3D PRINTING

DATE:

Thursday, September 26, 2013 

 

PLACE :

Raffel’s – 10160 Reading Road (see below for directions)

TIME :

5:30 p.m. to 6:00 p.m. –  Social Time

 

6:00 p.m. to 7:00 p.m. –  Dinner

 

7:00 p.m. to 8:45 p.m. –  Presentation

COST

$10- $15, See information in Reservations

   

 

 

 We will be awarding 10 Free dinners to any future section meeting!!!

ABOUT THE MEETING:   

Create jet engines in the comfort of your living room?  Not quite, but local expert Ted Anderson of GE will show how GE is now using 3D printing/ Additive Manufacturing to create intricate engine components from CAD to complete parts in days, not months using Direct Metal Laser Sintering, and Electron Beam Melting.

Since 2003, Morris Technologies, Inc. http://www.morristech.com/Technologies/ has been known for its extensive capabilities utilizing Direct Metal Laser Sintering (DMLS) to produce complex geometries.  The process uses a high power laser and scanner system to fuse fine metal powder layer by layer to create fully dense parts. With the proper thermal treatments, these ‘grown’ components exhibit near wrought properties. 

Electron Beam Melting is an additive manufacturing process that uses multiple high-power electron beams to melt layers of metal powder into complex forms and shapes.  EBM grows parts in a vacuum environment, eliminating the need for post-build stress relieving and enabling parts to be grown using thicker layers than other technologies.

Published on May 22, 2013

GE Aviation is revolutionizing the age-old rules of manufacturing and design. Learn how additive manufacturing, a 3D printing technology, frees engineers to design the perfect jet engine.

http://youtu.be/l0SXlkrmzyw

 ABOUT THE PRESENTER:  

Ted Anderson has a BSME, MSME, and an MBA.  Ted got his big start with additive manufacturing/3D printing in 2005 while researching a flexible surface with multiple degrees of freedom that he was building using a stereolithography (SLA) system.  His career in additive manufacturing includes working for Georgia Tech, Arcam AB, Raytheon as a contractor for NASA, and his current employer GE.  He has experience working with multiple platforms that includes metals, plastics, and electronics.  The systems he has experience with includes fused deposition modeling (FDM), selective laser sintering (SLS), MultiJet, SLA, electron beam melting (EBM), direct metal laser sintering (DMLS) and selective laser melting (SLM)

 MENU SELECTIONS:

Baked Tilapia with Lemon Caper Sauce, Stuffed Pork Chops, Grilled Portobello w/ Ratatouille & Yellow Rice

Sautéed Vegetables, Tossed Salad, Dinner Rolls and Butter, Chef’s Choice Dessert

LOCATION:  Raffel’s is located at 10160 Reading Road, south of Glendale-Milford Road on the east side of Reading. Take I-75 to the Glendale-Milford Rd. Exit, go east on Glendale-Milford Road approximately ¾ of a mile to Reading Rd. and turn right on Reading.

 RESERVATIONS:  Please make reservations for each meeting by going to: https://ieeecincinnati.org/meetings/.  Please click on the appropriate link and complete the reservation. 

Reservations close at midnight on September 22, 2013.

DINNER RESERVATION CANCELLATION POLICY
An email to Reservations@ieeecincinnati.org prior to the close of reservations is required to properly cancel your reservation.

All Reservations must be made by midnight, Sunday September 22, 2013

 PE CREDITS:  Depending on the subject matter, attendance at IEEE Cincinnati Section Meetings now qualifies the attendee for Professional Development Hours towards renewal of Professional Engineers Licenses. Required documentation will be available following the meeting!  The Section Meetings also provide a great opportunity to network with fellow engineers in the area.